Pour the Canna butter over the tortilla so that it covered and gently move it around
Take a spoonful of cinnamon and two spoons of sugar band pour it around the tortilla and let it sit until sugar and cinnamon dissolve and then wrap tortilla up and eat and enjoy the delicious taste
First step to making marijuana (weed, bud, ganja, dank, etc) hot chocolate is ingredients:
5 Grams of finely grind ed grounded up weed (Marijuana, bud, ganja, dank, etc)
1/3 cups of milk 1 per serving
1/2 cups of light cream 1 per serving
Toaster Oven
baking sheet or tin foil
pan
As many hot chocolate serving that needed
Step two is to take the baking sheet of the tin foil and place the the finely grind ed grounded marijuana on the baking sheet or wrap it in the tin foil
Step Three preheat the toaster or oven to 270 degrees Fahrenheit and place the baking sheet or tin foil in for 15 minutes. This is turning the THC into a psychoactive THC. The marijuana will smell and steam during the process ordinary it also will turn the color brown but that average.
Step four Mix the milk and the light cream on the stove in a pan on low heat.
Step Five add the finely grind ed grounded marijuana
Step Six keep the boiling milk, cream, and marijuana on low if it boils over the heat is too high take the heat off until it cool and put it back on low heat
Strain into cup or a mug and squeeze the marijuana to get the milk out
Add Hot Chocolate Mixture
add any flavor such a vanilla,almonds, french vanilla, pumpkin spice to simmer a nice flavor added alcohol will dissolve some THC
Drink it on a completely empty stomach to fill the full effect of the high
The stronger the weed the better the high
I Might take a couple of hour depend on how much is dunking
Here a video tutorial on how to make pot hot chocolate
This is a tutorial video on how to cook a meal made out marijuana. This tutorial video is going to show you learners how to make spaghetti out of bud garlic bread out of bud and brownies out of bud
ingredients:
A Ounce Of Weed
Brownie mixture
Butter
Eggs
Milk
Bread
Spaghetti strings or noodles
Electric Grinder
Large Pot
Oil
Onion
Tomato Paste or Sauce
Garlic powder
Pepper
Salt
Ground Beef
Large Bowl
Watch Video On instruction on how to make this meal step by step carefully and briefly follow replay video if necessary
First Step to making a homemade vaporizer is the supplies:
Light Bulb
screw driver
bottle cap
knife
small tube
Second step is to carefully and slowly cut the metal tip of the light bulb away from the ceramic base
After you bend the tip you can take or pry the metal piece off
Third Step is to use the knife and apply pressure to the center hole that the metal tip was taken from
Twist the knife in the center so that the ceramic base will crack after you crack the ceramic base remove the rest with a knife
Step four use the screw driver to crack the inner side of the light bulb carefully without breaking the outer bulb empty inner bulb inside trash
Step Five Wash the light bulb in hot water and soap make sure the bulb is clean inside and out
Step six poke a hole in the cap with a screw driver or knife make sure the hole is large enough to fit the tube perfectly
if the hole is not a good fit try again
Step seven Grind up your marijuana( Bud, ganja, weed, etc) and place inside the inner bulb the screw the cap on the metal base
You finally Finished creating the light bulb vaporizer Now time to enjoy and use
here and video on how to make a light bulb vaporizer
Second Way to Make Homemade Light bulb Vaporizer
Step One to making homemade vaporizer is materials:
Clear Light bulb
knife
Electrical Tape
Two Hollowed Out Pens
Cap From Two Liter Bottle
Hot Glue Gun
Candle
Lighter
Marijuana
Follow instruction carefully for a seal tight Vaporizer
Step one carefully remove the top metal tip of the light bulb included all the blackish purplish material at the end try not to mess up the metal
Step Two Clean out the filaments inside the inner bulb into trash then clean out with warm water and soap and don't forget to wash the outer bulb
+
Step Three Take your cap and puncture two in it make sure your holes are big enough to fit your pens tubes threw Hot Glue them in place so that they are secure
Step five grind of the marijuana until it powdery take bottle cap with the secure pens to the metal part of the light bulb
Step six use the electrical tape to make the cap of the light Bulb vaporizer airtight to get a perfect hit
Step seven light and candle and hold the bulb 1inche away from the flame until you see a transparent vapor inside the bulb don't forget to have two finger cover the holes as this is done
Step eight uncover both hole and inhale thew bigger and longer tube
Here a video on how to make your own custom vaporizer