Monday, November 21, 2011

Marijuana Cinnamon And Sugar Tortilla

Marijuana Cinnamon And Sugar Tortilla

Canna Butter

Put A tortilla in a cooking pan on low

Pour the Canna butter over the tortilla so that it covered and gently move it around

Take a spoonful of cinnamon and two spoons of sugar band pour it around the tortilla and let it sit until sugar and cinnamon dissolve and then wrap tortilla up and eat and enjoy the delicious taste

Marijuana Hot Chocolate Recipe

Marijuana Hot Chocolate Recipe

First step to making marijuana (weed, bud, ganja, dank, etc) hot chocolate is ingredients:

5 Grams of finely grind ed grounded up weed (Marijuana, bud, ganja, dank, etc) 
1/3 cups of milk 1 per serving
1/2 cups of light cream 1 per serving
Toaster Oven 
baking sheet or tin foil
As many hot chocolate serving that needed

Step two is to take the baking sheet of the tin foil and place the the finely grind ed grounded marijuana on the baking sheet or wrap it in the tin foil

Step Three preheat the toaster or oven to 270 degrees Fahrenheit and place the baking sheet or tin foil in for 15 minutes. This is turning the THC into a psychoactive THC. The marijuana will smell and steam during the process ordinary it also will turn the color brown but that average.

Step four Mix the milk and the light cream on the stove in a pan on low heat.
Step Five add the finely grind ed  grounded marijuana

Step Six keep the boiling milk, cream, and marijuana on low if it boils over the heat is too high take the heat off until it cool and put it back on low heat

Strain into cup or a mug and squeeze the marijuana to get the milk out

Add Hot Chocolate Mixture

add any flavor such a vanilla,almonds, french vanilla, pumpkin spice to simmer a nice flavor added alcohol will dissolve some THC

Drink it on a completely empty stomach to fill the full effect of the high
The stronger the weed the better the high

I Might take a couple of hour depend on how much is dunking

Here a video tutorial on how to make  pot hot chocolate

Homade Materials Use To Get Rid Of Weed Smell

The Sploof
The Sploof was made to mask the strong  smell of weed
The sploof is homemade material use from your daily house hold  materials
Brown Roll From Paper towel
Dryer Sheet Fabric softener
and tape
Here a video on how to make one in 2 minutes

Sunday, November 20, 2011

How To Cooking A Marijuana Meal

This is a tutorial video on how to cook a meal made out marijuana. This tutorial video is going to show you learners how to make spaghetti out of bud garlic bread out of bud and brownies out of bud 
A Ounce Of Weed
Brownie mixture
Spaghetti strings or noodles
Electric Grinder
Large Pot
Tomato Paste or Sauce
Garlic powder
Ground Beef
Large Bowl

Watch Video On instruction  on how to make this meal step by step carefully and briefly follow replay video if necessary

Two Different Ways To Make A Marijuana Vaprizor

Homemade Marijuana Vaporizer

First Step to making a homemade vaporizer is the supplies:

Light Bulb
screw driver 
bottle cap
small tube

Second step is to carefully and slowly cut the metal tip of the light bulb away from the ceramic base
After you bend the tip you can take or pry the metal piece off

Third Step is to use the knife and apply pressure to the center hole that the metal tip was taken from
Twist the knife in the center so that the ceramic base will crack after you crack the ceramic base remove the rest with a knife

Step four use the screw driver to crack the inner side of the light bulb carefully without breaking the outer bulb empty inner bulb inside trash

Step Five Wash the light bulb in hot water and soap make sure the bulb is clean inside and out

Step six poke a hole in the cap with a screw driver or knife make sure the hole is large enough to fit the tube perfectly
if the hole is not a good fit try again

Step seven Grind up your marijuana( Bud, ganja, weed, etc) and place inside the inner bulb the screw the cap on the metal base

You finally Finished creating the light bulb vaporizer Now time to enjoy and use
 here and video on how to make a light bulb vaporizer

Second Way to Make Homemade Light bulb Vaporizer

Step One to making homemade vaporizer is materials:
Clear Light bulb
Electrical Tape
Two Hollowed Out Pens

Cap From Two Liter Bottle

Hot Glue Gun




Follow instruction carefully for a seal tight Vaporizer

Step one carefully remove the top metal tip of the light bulb included all the blackish purplish material at the end try not to mess up the metal

Step Two Clean out the filaments inside the inner bulb into trash then clean out with warm water and soap and don't forget to wash the outer bulb

Step Three Take your cap and puncture two in it make sure your holes are big enough to fit your pens tubes threw Hot Glue them in place so that they are secure

Step five grind of the marijuana until it powdery take bottle cap with the secure pens to the metal part of the light bulb  

Step six use the electrical tape to make the cap of the light Bulb vaporizer airtight to get a perfect hit

Step seven light and candle and hold the bulb 1inche away from the flame until you see a transparent vapor inside the bulb don't forget to have two finger cover the holes as this is done

Step eight uncover both hole and inhale thew bigger and longer tube

Here a video on how to make your own custom vaporizer